Efoxcity 12V 1156 10 Pack Bright 1156 1141 1003 50-SMD White LED Bulbs For Car Interior RV Camper light
- Voltage: DC 12V,Flux:650 Lumens,Cerrent:0.17A
- Warning:The 1156 bulb only used for 12VDC,Please make sure your car voltage is 12V.
- Fit:1156 BA15S 1073 1095 1141 1156 1156A 1156NA 1195 12088 1295 1295NA 199 2396 3497 631 7506 93 97 97A 97NA
- Application:Backup Reserve Light,Tail light, Corner light, Stop light, Parking light, Side marker light, ect. Common use for Car, Truck, Trailer, RV, etc.
- Tips:Any issue or problem please feel free to contact with us before write a product review or feedback,we provde best service for u at first time.
Geetanjali Gajadar
These bulbs work great in my RV and I can now run several ...
These bulbs work great in my RV and I can now run several lights at night without worrying too much about depleting my batteries. They draw about .19 amps each compared to the 1.2/1.3 of the old incandescent bulbs. That's about 1/6 of the current so it is a huge difference. I have not noticed any burning smell or anything like some others have mentioned, but I did find some of my fixtures were wired backwards which caused the bulbs not to work. A quick flip-flop of the wiring and they worked fine after that. I replaced 7 fixtures so I still have 3 bulbs left for spares.
Muhammad Ramzan
Very Happy With These Bulbs
Used these to replace old incandescent lamps and they work great. I love that they don't get hot, and I also like the bluer light they give off. They did not work at all in a lamp that had three settings. I had hoped that they would at least turn on in that lamp, but I guess the circuitry was made for incandescent bulbs. Not counting that against this product, though. Very satisfied.
Kamal Kumar Rajak
Do it! Change to LED.
Slightly brighter and cleaner color of light than the incandescents. I bought 30 and all lights work. The lumens are appropriate for regular lighting. The 10 packs are the best value I can find and the quality is not disappointing. Excellent return on investment for a simple RV upgrade.
Derek Hall
These are bright AF tho
These are excellently bright. Great for running lights of all types. Anywhere you need an 1156, the one with a single filament and two bumps on the same level, you need this baby. It's so bright, that it honestly doesn't work well with amber lights, as it makes it less yellow than a traditional bulb. Do with that information what you will. These are bright AF tho
Becky Johnson
Very good bulbs
I got these to replace the automotive type 1141 parallel pin bulbs throughout my travel trailer. It is like daylight in there at night now instead of that soft glow and they use very little power as most of the energy is released as light instead of heat.
Rod Mackay
Very Bright Lights
Very Bright Lights used to replace old lights in my 1970s camper trailer. These are much brighter than the old lights and I find that I need fewer lights on to get more lighting in the trailer/
Yvonne Hines
Buy These
I put these in my camper. They are much brighter than the original lamps and will use much less energy.
Jake Barnes
Great for RV interior and tail/backup lights
I bought the more expensive 2-pack at the same time as these. The more expensive ones had 54 smd chips and these had 50. When comparing them, there was no discernable (to the eye) difference as either backup lights or turn signals, very bright. The 10 pack is a great bargain. I used 6 of them for my motorhome interior ceiling lights and they have a brighter whiter light than the old incandescent bulbs.
Sharath Sukumar
Good replacement for old lights
Replaced all interior lights in my RV, nice white light, not super bright, but better than old incandescent. All lights worked as expected. Would buy again if needed.
Ben Fredj Sahar
So far so good
I've only had these a few days, but so far I have tested them and all (10) function properly. I'll come back if/when they start failing. As expected, the quality of construction is at the lowest level and just enough to be functional. I'd imagine this is why they fail so quickly. It didn't take me much time at all to go through these bulbs and re-solder the connections...I'd be willing to bet that this is the source of the failures.